In this guide, you’ll find a comprehensive table of common United tractor error codes, their meanings, possible causes, and recommended solutions.
Keep in mind that some codes may vary depending on the tractor model and engine manufacturer (such as Perkins, Yanmar, Kubota, or other engines used in different United tractor models).
United Tractor Error Codes
| Error Code | System | Meaning | Possible Causes | Recommended Solution |
|---|---|---|---|---|
| E001 | Engine | Engine coolant temperature high | Low coolant, clogged radiator, faulty thermostat | Check coolant level, clean radiator, inspect cooling system |
| E002 | Engine | Engine oil pressure low | Low oil level, worn oil pump, clogged filter | Add oil, replace filter, inspect oil pump |
| E003 | Engine | Engine speed sensor fault | Damaged sensor, loose wiring | Inspect wiring and replace sensor if necessary |
| E004 | Engine | Crankshaft position sensor error | Failed sensor, electrical issue | Test and replace crankshaft sensor |
| E005 | Engine | Camshaft position sensor fault | Faulty sensor or connector | Inspect wiring and replace sensor |
| E006 | Fuel | Fuel pressure too low | Dirty fuel filter, weak fuel pump | Replace fuel filter and inspect pump |
| E007 | Fuel | Water detected in fuel | Contaminated diesel | Drain water separator and replace fuel |
| E008 | Fuel | Injector malfunction | Dirty or faulty injector | Clean or replace injector |
| E009 | Fuel | Fuel rail pressure sensor error | Sensor failure | Replace pressure sensor |
| E010 | Intake | Air intake restriction | Dirty air filter | Replace or clean air filter |
| E011 | Turbo | Turbocharger boost pressure low | Air leak, worn turbo | Inspect hoses and turbocharger |
| E012 | Exhaust | Exhaust temperature high | DPF issue, overloaded engine | Reduce load and inspect exhaust |
| E013 | Electrical | Battery voltage low | Weak battery, faulty alternator | Charge battery and test charging system |
| E014 | Electrical | Charging system failure | Bad alternator, loose belt | Replace alternator or tighten belt |
| E015 | Electrical | ECU communication failure | Wiring issue or ECU fault | Inspect connectors and perform ECU diagnostics |
| E016 | Electrical | CAN Bus communication error | Damaged wiring or control module | Check CAN Bus wiring |
| E017 | Engine | Glow plug circuit fault | Failed glow plug | Replace faulty glow plug |
| E018 | Engine | Intake air temperature sensor fault | Bad sensor | Replace intake temperature sensor |
| E019 | Engine | Coolant temperature sensor fault | Failed sensor | Install new coolant sensor |
| E020 | Engine | Engine overspeed | Operator error or governor issue | Reduce throttle and inspect governor |
Related AGCO Tractor Error Codes(All Errors, Causes + Solutions)
Hydraulic System Error Codes
| Error Code | Meaning | Possible Causes | Solution |
|---|---|---|---|
| H001 | Hydraulic pressure low | Low hydraulic oil, pump wear | Refill oil and inspect pump |
| H002 | Hydraulic oil temperature high | Dirty cooler, overloaded hydraulics | Clean cooler and reduce load |
| H003 | Hydraulic filter clogged | Dirty filter | Replace hydraulic filter |
| H004 | Hydraulic pump fault | Internal pump wear | Inspect and rebuild pump |
| H005 | Hydraulic pressure sensor error | Faulty sensor | Replace pressure sensor |
| H006 | Hydraulic control valve fault | Valve sticking | Clean or replace valve |
| H007 | Three-point hitch sensor fault | Position sensor failure | Replace hitch sensor |
| H008 | Hydraulic oil level low | Oil leak | Repair leak and refill oil |
Related Solis Tractor Error Codes(All Errors, Causes + Solutions)
Transmission Error Codes
| Error Code | Meaning | Possible Causes | Solution |
|---|---|---|---|
| T001 | Transmission oil pressure low | Low oil, pump failure | Check oil level and pump |
| T002 | Transmission overheating | Heavy load, dirty oil cooler | Clean cooler and replace oil |
| T003 | Gear shift sensor fault | Damaged sensor | Replace shift sensor |
| T004 | Clutch position sensor error | Sensor failure | Install new sensor |
| T005 | Transmission control module error | ECU fault | Perform diagnostics |
| T006 | Gear engagement failure | Mechanical wear | Inspect gearbox |
| T007 | Transmission oil temperature sensor fault | Sensor malfunction | Replace sensor |
| T008 | PTO clutch fault | Worn PTO clutch | Inspect and replace clutch |
Related Big Bud Tractor Error Codes(All Errors + Solutions)
PTO Error Codes
| Error Code | Meaning | Possible Causes | Solution |
|---|---|---|---|
| P001 | PTO speed sensor fault | Sensor damaged | Replace speed sensor |
| P002 | PTO overload | Heavy implement | Reduce load |
| P003 | PTO clutch overheating | Slipping clutch | Replace clutch components |
| P004 | PTO switch fault | Defective switch | Replace switch |
| P005 | PTO engagement error | Electrical issue | Inspect PTO wiring |
Related New Holland Tractor Error Codes(All Codes + Solutions)
Brake System Error Codes
| Error Code | Meaning | Possible Causes | Solution |
|---|---|---|---|
| B001 | Brake fluid low | Leak or worn pads | Refill fluid and repair leak |
| B002 | Parking brake switch fault | Switch failure | Replace switch |
| B003 | Brake pressure sensor fault | Faulty sensor | Install new sensor |
| B004 | Brake pedal sensor error | Sensor failure | Replace pedal sensor |
Steering Error Codes
| Error Code | Meaning | Possible Causes | Solution |
|---|---|---|---|
| S001 | Steering angle sensor fault | Damaged sensor | Replace steering sensor |
| S002 | Power steering pressure low | Low hydraulic oil | Check hydraulic system |
| S003 | Steering control module error | ECU problem | Diagnose control module |
| S004 | Steering motor overload | Heavy steering load | Inspect steering components |
Related Lawn Mower Warning Signs(12 Common, Causes + Fixes)
Electrical Error Codes
| Error Code | Meaning | Possible Causes | Solution |
|---|---|---|---|
| EL001 | Fuse blown | Electrical short | Replace fuse and locate short |
| EL002 | Starter relay fault | Bad relay | Replace relay |
| EL003 | Starter motor failure | Worn starter | Repair or replace starter |
| EL004 | Ignition switch fault | Defective switch | Install new ignition switch |
| EL005 | Alternator overvoltage | Faulty regulator | Replace voltage regulator |
| EL006 | Battery temperature high | Charging problem | Test charging system |
| EL007 | Ground circuit fault | Loose ground wire | Tighten ground connections |
| EL008 | Sensor power supply fault | Wiring issue | Inspect electrical harness |
Related TYM Tractor Error Codes(All Errors, Causes + Solutions)
Common Causes of United Tractor Error Codes
Most United tractor fault codes are triggered by maintenance issues rather than major mechanical failures. The most common causes include:
- Dirty fuel filters
- Low engine oil
- Low hydraulic oil
- Dirty air filters
- Weak batteries
- Damaged wiring
- Loose electrical connectors
- Faulty sensors
- Clogged radiators
- Poor maintenance intervals
Routine servicing can prevent many of these issues before they trigger warning codes.
How to Clear United Tractor Error Codes
Many temporary error codes will clear automatically after the fault has been corrected. Follow these steps:
- Turn off the tractor.
- Repair the underlying issue.
- Restart the engine.
- Allow the ECU to complete its system check.
- If the code remains, use a compatible diagnostic scan tool to erase stored fault codes.
- If the same code returns immediately, additional diagnosis is required.
Never clear an error code without fixing the underlying problem, as doing so may lead to more serious equipment damage.
Preventing Future Error Codes
The best way to avoid recurring error codes is through preventive maintenance. Follow the service intervals recommended for your specific United tractor model and inspect the machine before each use.
Key maintenance tips include:
- Change engine oil and filters on schedule.
- Replace fuel filters regularly.
- Clean the radiator and cooling fins.
- Keep hydraulic oil at the proper level.
- Inspect electrical connectors for corrosion.
- Charge and maintain the battery.
- Replace damaged sensors promptly.
- Use clean, high-quality diesel fuel.
- Check belts and hoses for wear.
- Lubricate moving components according to the maintenance schedule.
Final Thoughts
United Tractor error codes are designed to help operators quickly identify developing problems before they become expensive repairs. While some warnings indicate simple maintenance needs, such as replacing a filter or topping up fluids, others may point to sensor failures, hydraulic faults, or transmission issues that require more detailed diagnosis.
By understanding what each code means and responding promptly, you can minimize downtime, extend the life of your tractor, and keep it operating safely and efficiently. Always refer to your specific United tractor service manual for model-specific diagnostic procedures, as fault codes and troubleshooting steps may differ between tractor models and engine configurations.
