This post will guide you through the most common John Deere Z930M error codes, what they mean, and how to fix them. We’ll also provide practical maintenance tips to avoid recurring issues and ensure your mower operates smoothly.
Z930M John Deere Error Codes
Error Code | Meaning | Possible Cause | Fix / Solution |
---|---|---|---|
E01 | Engine oil pressure low | Low oil level, worn oil pump, faulty sensor | Check oil level, replace sensor or pump |
E02 | Engine temperature too high | Blocked cooling fins, low coolant, bad sensor | Clean fins, check coolant, replace sensor |
E03 | Battery voltage too low | Weak battery, bad alternator, corroded terminals | Recharge battery, clean terminals, replace alt. |
E04 | PTO engagement error | Faulty switch, wiring issue | Inspect PTO switch, clutch, and connections |
E05 | Seat switch not engaged | Operator not seated, faulty seat switch | Sit properly, replace or reconnect seat switch |
E06 | Reverse switch error | Defective reverse switch or wiring | Check/replace reverse switch and wires |
E07 | Neutral start switch error | Levers not in neutral, switch fault | Return controls to neutral, inspect switch |
E08 | Parking brake not engaged | Brake not set, sensor fault | Set brake fully, test/replace switch |
E09 | Mower deck lift error | Hydraulic/lift sensor problem | Check deck lift system and wiring |
E10 | Fuel cap sensor error | Loose or faulty sensor near fuel tank | Tighten cap, check or replace sensor |
E11 | Fuel sensor failure | Open/short in fuel level circuit | Inspect wiring, test sensor |
E12 | Air intake temperature error | Damaged intake sensor or clogged filter | Replace sensor, clean/replace air filter |
E13 | Engine speed sensor error | Sensor not reading RPM, loose connector | Replace or reconnect engine speed sensor |
E14 | Hydraulic oil temperature too high | Low fluid, clogged cooler | Check fluid level, clean cooler |
E15 | Transmission pressure too low | Fluid leak, worn pump | Inspect system, refill or repair |
E16 | CAN communication failure | Damaged wiring, controller issue | Inspect CAN harness, replace controller |
E17 | Tilt sensor malfunction | Tilt angle sensor fault | Test or replace tilt sensor |
E18 | Glow plug circuit error (diesel models) | Failed glow plug or relay | Replace glow plug or glow plug relay |
E20 | Engine shutdown due to critical fault | Multiple system failures | Check stored codes, call technician |
Note: Error codes may vary slightly by model year and configuration.
Related John Deere ZTrak Mower E1 Error(4 Causes + Solutions)
What Are Error Codes on the Z930M?
Error codes on the Z930M are part of the mower’s onboard Electronic Control Unit (ECU) diagnostics system. When the ECU detects a problem, whether it’s electrical, mechanical, or safety-related, it generates a code to indicate the fault. These codes usually display on the mower’s TechControl™ display or dashboard screen.
Understanding these codes can help you:
- Identify the root cause of a problem.
- Decide whether it’s something you can fix yourself or requires professional service.
- Prevent further damage by addressing issues early.
Related John Deere Fault Code List(Error Code A to Z)
How to Access Diagnostic Trouble Codes on the Z930M
To view or clear error codes on your John Deere Z930M:
- Turn the key switch to the ON position, but do not start the engine.
- On the display, press and hold the right arrow or menu button (depending on display type) for a few seconds.
- Navigate to the Diagnostics menu.
- Choose Fault Codes or Active Errors to see a list.
- Use the arrow keys to scroll through the codes.
- To clear codes, some models allow clearing inactive codes after resolving the issue.
Related John Deere Z335E Code E2(4 Common Causes + Solutions)
Troubleshooting Tips for Common Z930M Errors
1. Engine Oil Pressure Warning (E01)
- Stop the engine immediately to prevent damage.
- Check the oil level and top up if necessary.
- If the oil is full, inspect the oil pressure sensor or consider replacing the oil filter.
2. PTO Not Engaging (E04)
- Ensure you’re sitting properly on the seat and the brake is engaged.
- Check the PTO switch for wear or corrosion.
- Inspect the wiring harness leading to the PTO clutch.
3. Battery Voltage Low (E03)
- Clean battery terminals.
- Test with a multimeter, should read 12.4V+ when off and 13.8-14.5V while running.
- Replace the alternator if the voltage doesn’t increase when running.
Related John Deere Code 94.18(Here’s How to Fix It!)
Preventative Maintenance to Reduce Error Codes
Proactive care is the best way to minimize error codes. Here’s how to keep your Z930M in top shape:
- Change engine oil and filter every 100 hours or seasonally.
- Clean radiator and cooling fins regularly to prevent overheating.
- Inspect wiring harnesses for signs of wear, corrosion, or animal damage.
- Keep the mower deck clean to avoid sensor obstructions.
- Check hydraulic fluid levels and ensure the parking brake operates smoothly.
When to Call a John Deere Technician
While many issues can be fixed at home with basic tools, some errors, like CAN communication faults (E16) or controller failures, require specialized tools and experience. If:
- The same code keeps reappearing after repairs,
- You’re unable to reset or clear the code,
- Multiple codes appear together without an obvious cause,
Get John deere support near you HERE
Related John Deere SPN Codes(A to Z Codes)
FAQs
What should I do if I see a flashing error code on my Z930M?
Flashing error codes typically indicate active faults that need immediate attention. Safely shut down the mower and refer to your operator’s manual or the diagnostic menu to interpret the code.
Can I clear Z930M error codes without fixing the issue?
No. Active codes will return if the underlying problem isn’t resolved. Clearing the code without fixing the issue may result in damage or unsafe operation.
Why does my Z930M keep showing the parking brake error?
This often means the brake switch is stuck, misaligned, or not fully engaged. Check the brake pedal travel and switch connector.
What causes CAN bus communication errors on the Z930M?
CAN bus errors (like E16) occur when modules fail to communicate, due to loose connectors, wiring faults, or failed controllers. These require professional diagnostics.
Final Thoughts
Error codes on your John Deere Z930M are like your mower’s way of speaking to you, don’t ignore them. Understanding what these messages mean and how to resolve them can help extend the life of your mower, improve safety, and avoid costly repairs.